Braeburn 1100 Manuel d'utilisateur télécharger pdf

MODEL

1100

Builder Series

Non-Programmable

2 Heat / 1 Cool

Multi-Stage Thermostat

Compatible with low voltage multi-stage

heat / cool systems with up to two stages of

heating and one stage of cooling.

WARNING!

Important Safety Information

• Always turn off power to the air conditioning or heating system prior to installing,

removing, cleaning or servicing thermostat.

• Read this manual thoroughly prior to installing, programming or operating

this thermostat.

• This thermostat is designed for use with a 24 Volt-AC low voltage multi-stage

heat / cool system.

• Do not use this thermostat on systems with voltages higher than 30 Volt-AC.

• This thermostat requires 24 Volt AC power for normal operation and control of

the heating or cooling system.

• In the event of an AC power outage, the ﬁrst and second stage temperature

differentials and the setpoint will return to their default system values. The user

can change the default settings once power is restored.

• Wiring must conform to all building codes and ordinances as required by local

and national code authorities having jurisdiction.

• Do not short (or jumper) across terminals on the gas valve or at the heating or

cooling system control board to test the thermostat installation. This could

damage the thermostat and void the warranty.

• Do not select COOL mode of operation if the outside temperature is below 50˚ F

(10˚ C). This could possibly damage the controlled cooling system and may

cause personal injury.

• This thermostat should only be used as described in this manual. Any other use

is not recommended and will void the warranty.

SPECIFICATIONS

• Electrical Rating: 24 Volt AC (18-30 Volt AC)

1 amp maximum load per terminal

3 amp total maximum load (all terminals)

• Control Range: 45˚ - 90˚ F (7˚ - 32˚ C)

• Accuracy: +/- 1˚ F (+/- .5˚ C)

• AC Power: 18-30 Volt AC

• Compatibility: Multi-stage heat / cool systems

with up to two stages of heating and one stage

of cooling.

• Terminations: R, O, B, C, Y, W1, G, W2

USER MANUAL

READ ALL INSTRUCTIONS BEFORE PROCEEDING

CONTENTS

SPECIFICATIONS

INSTALLATION

TESTING YOUR NEW THERMOSTAT

PROGRAMMING USER SETTINGS

ADDITIONAL OPERATION FEATURES

TROUBLESHOOTING

WIRING DIAGRAM

Front

1 2 3 4 5

Résumé du contenu

Page 1 - USER MANUAL

MODEL1100Builder Series Non-Programmable2 Heat / 1 CoolMulti-Stage ThermostatCompatible with low voltage multi-stage heat / cool systems with up to tw

Page 2 - NEW THERMOSTAT

2 3INSTALLATION22.2Installing Your New Thermostat2.2Installing Your New Thermostat cont.NOTE: If you are installing this thermostat in a new installa

Page 3

4PROGRAMMINGUSER SETTINGS44.1Default Thermostat Settings4.2Setting Temperature DifferentialSetting First Stage DifferentialNOTE: The ﬁrst and second

Page 4 - SYMPTOM POTENTIAL SOLUTION

67Resetting ThermostatNon-Volatile MemoryThe Reset feature allows the user to completely reset the thermostat and to register new manual ˚F / ˚C tempe

Page 5 - R Y W1 W2GO B C

8WIRING DIAGRAM7The room is too warm or too cold.See Review Set Temperature section of this manual to verify the current setpoint and make any modiﬁca

Commentaires sur ces manuels

Pas de commentaire

Braeburn 1100 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Braeburn 1100. Braeburn 1100 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Braeburn 1100