Braeburn 5200 Spécifications télécharger pdf

WARNING

Important Safety Information

• Always turn off power to the air conditioning or heating system prior to

installing, removing, cleaning or servicing thermostat.

• This thermostat requires either 24 Volts AC Power or two (2) properly installed

“AA” alkaline batteries for normal operation and control of the heating or

cooling system.

• This thermostat requires two (2) properly installed “AA” alkaline batteries to

retain clock setting in the event of loss of AC Power due to a power outage or

rolling blackouts when used as a hardwired thermostat.

• This thermostat should only be used as described in this manual. Any other

use is not recommended and will void the warranty.

Speciﬁcations

• Compatibility: Compatible with low voltage multi-stage gas, oil or electric

heating or cooling systems, including multi-stage heat pumps.

• Terminations: R, O, B, C, Y1, Y2, E/W1, W2, G, L

Speciﬁcations

cont.

Installation

• Electrical Rating: 24 Volt AC (18-30 Volt AC)

1 amp maximum load per terminal

3 amp maximum load (all terminals)

• Control Range: 45˚ - 90˚ F. (7˚ - 32˚ C)

• Accuracy: +/- 1˚ F. (+/- .5˚ C)

• AC Power: 18-30 Volt AC

• DC Back-Up Power: 3.0 Volt DC (2 AA Alkaline batteries included)

Speciﬁcations

Installation

Programming Installer Settings

Testing Your New Thermostat

Programming User Settings

Setting Your Energy

Saving Programs

Temperature Adjustment

Additional Operation

Features

Battery Replacement

Troubleshooting

Wiring Diagrams

MODEL

Up to 2 Heat / 2 Cool

7 Day, 5 - 2 Day or Non-Programmable

Conventional and Heat Pump

5200

Before Installing, Programming or Operating,

PLEASE READ ALL INSTRUCTIONS

5200-100-012

Replacing Existing Thermostat

Most thermostats have three parts:

• The cover, which may snap or hinge over the existing thermostat.

• The electronics or body, which controls the existing system.

• The sub-base, where the wires attach through the wall to the existing system.

1. Always turn off power to the air conditioning and heating system prior to

removing existing thermostat.

2. Carefully remove the cover and electronics body from the old thermostat

sub-base. Depending on the brand, these parts may pull off or need to be

unscrewed. The old sub-base should remain wired and on the wall until steps

4 and 5.

3. Label every old wire with the letter of the connection to which the wire is

attached. Example letters are R, M, and Y etc. Depending on the brand of the

old thermostat, your letters may be different.

4. After labeling the old wires, loosen each connection and remove them from

old sub-base. Secure the wires to prevent them from slipping into the hole in

the wall.

5. Remove the old sub-base from the wall, again being careful that the wires do

not slip into the hole in the wall.

6. Use the chart below to determine the new thermostat connections. As an

example, if the old thermostat had a G or F connection, it goes to G on the new

thermostat. Using a pencil and the chart below, circle the letter of each wire

removed from the old thermostat.

Old Terminal from

Existing Thermostat

New Terminal for

New Thermostat

Terminal Description

R, V-VR, or VR-R R 24 Volt AC

O or R O Reversing Valve (Cooling)

B B Reversing Valve (Heating)

C, X C 24 Volt AC, Transformer

Common

Y, Y1 or M Y1 Stage 1 Compressor

Y2 Y2 Stage 2 Compressor

E, W1 or W-U E/W1 Emergency Heat / 1st Stage Heat

W2 W2 Stage 2 Heating

G or F G Fan Control

L or X L System Status LED

NOTE: This thermostat is designed for use with 24 Volt-AC low voltage

multi-stage gas, oil or electric heating or cooling systems, including multi-stage

heat pump systems. Do not use this thermostat on applications with voltages

above 30 Volts AC.

Premier Series

Programmable Thermostats

1 2 3 4 5 6 ... 10 11

Résumé du contenu

Page 1 - Premier Series

WARNINGImportant Safety Information1• Always turn off power to the air conditioning or heating system prior to installing, removing, cleaning or

Page 2 - Installation

Troubleshootingcont.Troubleshootingcont.Symptom: HI is shown in the thermostat display where the room temperature is normally displayed.Potential Sol

Page 3 - Function Status After RESET

Wiring Diagrams11RY1 Y2W2GO B C E/W1Conventional Systems(See NOTE 1)Transformer Common Required1st Stage CompressorContact2nd Stage CompressorContactA

Page 4 - Programming User Settings

23Default Thermostat SettingsAt initial power up or after Installer CLEAR is pressed, the thermostat is reset to factory defaults. Installer CLEAR is

Page 5

45Programming Installer Settings3cont.When the User RESET button is pressed, the following options will reset to the factory defaults. All other setti

Page 6

6 7NOTE: Test your thermostat prior to programming any user settings. Pressing the Installer CLEAR button will reset the thermostat to all factory def

Page 7 - Additional Operation Features

8 9Setting Thermostat User OptionsThe default user options are compatible with most systems and applications. They are normally set at the time of ins

Page 8

10NOTE: If the 7 day programming mode was selected during the Installer Setup (section 3), the default program will use the weekday times and tempera

Page 9 - Battery Replacement

Entering Your Program1. Place the system switch in the HEAT mode of operation. 2. Press the PROG button to enter Program setting mode. The MORN s

Page 10 - Troubleshooting

Low Battery DetectionThis thermostat requires two (2) new, properly installed “AA” Alkaline batteriesto maintain the system clock and to provide prope

Page 11 - LIMITED WARRANTY

Additional Operation Features8This thermostat provides one type of cold weather compressor protection by locking out the compressor stage (1st Stage)