Braeburn 530 Spécifications télécharger pdf

WARNING

Important Safety Information

Builder Series

Non-Programmable Thermostats

Single Stage Heat / Cool

Conventional and Heat Pump

Multi-Stage 2 Heat / 1 Cool

Conventional and Heat Pump

• Always turn off power to the air conditioning or heating system prior to

installing, removing, cleaning or servicing thermostat.

• This thermostat requires either 24 Volts AC Power or two (2) properly installed

“AA” alkaline batteries for normal operation and control of the heating or

cooling system. Refer to “Low Battery Detection and Replacement” section for

more information.

• This thermostat should only be used as described in this manual. Any other

use is not recommended and will void the warranty.

Speciﬁcations

Installation

Testing Your New Thermostat

Programming User Settings

Temperature Adjustment

Additional Operation

Features

Battery Replacement

Troubleshooting

Wiring Diagrams

Speciﬁcations

• Electrical Rating: 24 Volt AC (18-30 Volt AC)

1 amp maximum load per terminal

2 amp total maximum load (all terminals) (Model 1000, 1000NC)

3 amp total maximum load (all terminals) (Model 1200, 1200NC)

• Control Range: 45˚ - 90˚ F (7˚- 32˚ C)

• Accuracy: +/- 1˚ F (+/- .5˚ C)

• AC Power: 18-30 Volt AC

• DC Power: 3.0 Volt DC (2 AA Alkaline batteries included)

• Model 1200, 1200NC: Compatibility with low voltage multi-stage gas, oil or

electric heating or cooling systems, including multi-stage heat pumps.

• Terminations, Model 1000, 1000NC: Rc, Rh, B, O, Y, W, G, C

• Terminations, Model 1200, 1200NC: R, O, B, C, Y1, E/W1, G, W2

Speciﬁcations

cont.

Installation

MODEL

Before Installing, Programming or Operating,

PLEASE READ ALL INSTRUCTIONS

• Model 1000, 1000NC: Compatibility with low voltage single stage gas, oil or

electric heating or cooling systems, including single stage heat pumps, can

also be used on 250mv to 750mv millivolt heating only systems.

Old Terminal from

Existing Thermostat

New Terminal for

New Thermostat

(1000, 1000NC)

New Terminal for

New Thermostat

(1200, 1200NC)

Terminal

Description

V or Rc Rc Cooling

Transformer

M, 4, Rh, or R Rh Heating

Transformer

R, V-VR or VR-R R 24 VAC

B B B Reversing Valve

(Heating)

O O O Reversing Valve

(Cooling)

Y, Y1 or M Y Y1 Cooling or

Compressor for

HP System

E, H, W, or 4 W E/W1 1st Stage Heat

or Emergency Heat

G or F G G Fan Control

C, X or B C C 24 VAC Common

1000, 1000NC

MODEL

1200, 1200NC

Replacing Existing Thermostat

Most thermostats have three parts:

• The cover, which may snap or hinge over the existing thermostat.

• The electronics or body, which controls the existing system.

• The sub-base, where the wires attach through the wall to the existing system.

1. Always turn off power to the air conditioning or heating system prior to

removing existing thermostat.

Carefully remove the cover and electronics body from the old thermostat sub-base.

Depending on the brand, these parts may pull off or need to be unscrewed. The

old sub-base should remain wired and on the wall until steps 4 and 5.

3. Label every old wire with the letter of the connection to which the wire is

attached. Example letters are R, M, Y etc. Depending on the brand of the old

thermostat, your letters may be different.

4. After labeling the old wires, loosen each connection and remove them from old

sub-base. Secure the wires to prevent them from slipping into the hole in the wall.

5. Remove the old sub-base from the wall, again being careful that the wires do

not slip into the hole in the wall.

6. Use the chart below to determine the new thermostat connections. As an

example, if the old thermostat had a G connection, it goes to G on the new

thermostat. Note the chart includes information for Braeburn

1000(NC) and

1200(NC) thermostats. Be sure to use the correct column for the new thermostat.

1 2 3 4 5 6 7

Résumé du contenu

Page 1 - Builder Series

WARNINGImportant Safety Information1Builder SeriesNon-Programmable Thermostats Single Stage Heat / Cool Conventional and Heat Pump Multi-Stage 2 Hea

Page 2 - Testing Your New Thermostat

2 3Installing New ThermostatWARNING!Read BEFORE TestingInstallation2cont.NOTE: If installing this thermostat in a new installation, locate the thermo

Page 3 - Temperature Adjustment

4Default Thermostat SettingsSetting Second Stage DifferentialSetting Temperature Differentials5Review Set Temperaturecont.Programming User Settings4Th

Page 4 - Battery Replacement

6Compressor Protection FeatureLow Battery Detection and ReplacementThis thermostat includes an automatic compressor protection feature to avoid potent

Page 5 - Wiring Diagrams

8 9cont.Symptom: OFF is shown in thermostat display and heating or cooling system will not start.Potential Solution: This indicates that the system is

Page 6

MODEL 1000, 1000NC: Single Stage Heat Pump SystemCompressorControlcont.Wiring Diagrams9Transformer Common(See NOTE 1)cont.Wiring Diagrams9R OReversin

Page 7 - LIMITED WARRANTY

Commentaires sur ces manuels

Pas de commentaire

Braeburn 530 Spécifications

Naviguer en ligne ou télécharger Spécifications pour Thermostats Braeburn 530. Braeburn 530 Specifications [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Thermostats Braeburn 530