Braeburn 5300 Spécifications télécharger pdf

Premier Series

Universal Auto Changeover

Up to 3 Heat / 2 Cool Heat Pump

or 2 Heat / 2 Cool Conventional Thermostat

Installer Guide

Speciﬁcations

Installation

Quick Reference

Programming Installer Settings

Before Installing, Programming or Operating,

PLEASE READ ALL INSTRUCTIONS

Testing Thermostat

Wiring Diagrams

5300

SEE USER MANUAL FOR TROUBLESHOOTING

WARNING

Important Safety Information

• Always turn off power to the air conditioning or heating system prior to

Installing, removing, cleaning or servicing thermostat.

• This thermostat is a dual power thermostat and either requires 24 Volt

AC Power or two (2) properly installed “AA” Alkaline batteries for normal

operation and control of the heating or cooling system.

• Properly installed batteries will allow the thermostat to retain clock settings in

the event of loss of AC Power due to power outage or rolling blackouts when

used as a hardwired thermostat.

• This thermostat should only be used as described in this manual. Any other

use is not recommended and will void the warranty.

Speciﬁcations

• Electrical Rating: 24 Volt AC (18-30 Volt AC)

1 amp maximum load per terminal

5 amp maximum load (all terminals)

• Control Range: 45º - 90º F (7º C - 32º C)

• Accuracy: +/- 1º F (+/- .5º C)

• AC Power: 18-30 Volt AC

• DC Power: 3.0 Volt DC (2 “AA” Alkaline batteries included)

Speciﬁcations

cont.

Replacing Existing Thermostat

Installation

Old Terminal from

Existing Thermostat

New Terminal for

New Thermostat

(Model 5300)

Terminal Description

A A External Air output

G or F G Fan Control

Rc Rc 24 Volt AC (Cooling for

Dual Transformer Systems)

R, V-VR or VR-R Rh 24 Volt AC

W1, W2 or W-U W2 Stage 2 Heating

B B Reversing Valve (Heating)

O or R O Reversing Valve (Cooling)

Y, Y1 or M Y1 Stage 1 Compressor

Y2 Y2 Stage 2 Compressor

W1/E/W3 W1/E/W3 1st Stage Heating for

Conventional Systems or

Emergency Heating for 3

Stage Heat Pumps

C, X or B C 24 Volt AC, Transformer

Common

L or X L System Malfunction Indicator

S1 S1 Optional Remote Sensor

S2 S2 Optional Remote Sensor

Most existing thermostats have three parts:

• The cover, which may snap or hinge over the existing thermostat.

• The electronics or body, which controls the existing system.

• The sub-base, where the wires attach through the wall to the existing system.

1. Always turn off power to the air conditioning and heating system prior to

removing existing thermostat.

2. Carefully remove the cover and electronics body from the old thermostat

sub-base. Depending on the brand, these parts may pull off or need to be

unscrewed. The old sub-base should remain wired and on the wall until

steps 4 and 5.

3. Label every old wire with the letter of the connection to which the wire is

attached. Example letters are R, M, Y, etc. Depending on the brand of the

old thermostat, your letters may be different. (continued on page 2)

Front when folded

• Compatibility: Compatible with low voltage single stage or multi-stage

Heat / Cool systems, including heat pumps with up to three stages of heating

and two stages of cooling, or conventional systems with up to two stages of

heating and two stages of cooling. This thermostat can also be used on 250 to

750 millivolt heating only systems.

• Terminations: A, G, Rc, Rh, W2, B, O, Y1, Y2, W1/E/W3, C, L, S1, S2

1 2 3 4 5 6 7 8 9 10

Résumé du contenu

Page 1 - Installer Guide

1Premier SeriesUniversal Auto ChangeoverUp to 3 Heat / 2 Cool Heat Pumpor 2 Heat / 2 Cool Conventional ThermostatInstaller Guide SpeciﬁcationsInstalla

Page 2 - Quick Reference

Store this booklet forfuture referenceBraeburn Systems LLC, as an Energy Star partner has determined that this product meets the Energy Star Guideline

Page 3 - (continued)

2 3Replacing Existing Thermostat (continued)SYSTEM Button: Selects AUTO (Heat/Cool), COOL, OFF, HEAT or EMER.PROG Button: Press to enter the program

Page 4 - Indoor Sensor must be

4Status After CLEAR–Factory Default SettingsAt initial power up or after Installer CLEAR is pressed, the thermostat is reset to factory defaults. Inst

Page 5

67cont.Programming Installer Settings4Setting Thermostat Installer OptionsThe Installer Options section allows the system and programming parameters t

Page 6

8cont.Programming Installer Settings4Setting Thermostat Installer Options (continued)1. Selects Residential or Commercial (BUS) proﬁle. Determines pro

Page 7 - Testing the Thermostat

10 11cont.Programming Installer Settings4Option Setting Temperature Controlsens I (Internal At Thermostat N/AThermostat Sensor)sens E (External At

Page 8 - Wiring Diagrams

12Testing the Thermostat5WARNING!Read BEFORE Testing• Do not short (or jumper) across terminals on the gas valve or at the heating or cooling sy

Page 9

Wiring Diagrams6Retain Factory Installed JumperNOTES: 1. Transformer Common connection not required for battery-only operation of thermostat. 2. Se

Page 10 - LI MITED

Wiring Diagrams cont.6NOTES: 1. Transformer Common connection not required for battery-only operation of thermostat. 2. Second Stage Control conne

Plus de documents pour Thermostats Braeburn 5300

Voir le document Braeburn 5300 Manuel d'utilisateur

Braeburn 5300 Manuel d'utilisateur (14 pages)

Braeburn 5300 Manuel d'utilisateur (15 pages)

Voir le document Braeburn 5300 Spécifications

Braeburn 5300 Spécifications (7 pages)

Commentaires sur ces manuels

Pas de commentaire

Braeburn 5300 Spécifications

Naviguer en ligne ou télécharger Spécifications pour Thermostats Braeburn 5300. Braeburn 5300 Specifications Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Thermostats Braeburn 5300

Commentaires sur ces manuels

Produits connexes et manuels pour Thermostats Braeburn 5300